Amana Washer Stuck on Sensing Fill: Troubleshooting guide

Amana washers stuck on sensing fill are a common issue. To fix it, you need to unplug the machine, plug it back in, and then start a new cycle.

If the issue persists, try cleaning the drain pump filter or checking the water supply valves. Having a washing machine that is not functioning correctly can be a real drag. One of the most common issues that can arise with an Amana washing machine is getting stuck in sensing fill mode.

This occurs when the washer does not recognize that there is enough water in the tub to begin the wash cycle, even though it is filled to the appropriate level. This can be both frustrating and time-consuming, but fortunately, it is not the end of the world. There are a few quick and straightforward fixes that you can try to get your machine back up and running in no time. In this article, we will go over some of the best ways to solve the Amana washer stuck-on sensing fill problem.

Troubleshooting Steps

When your Amana washer gets stuck on sensing fill, it can be frustrating. However, there are several troubleshooting steps you can take to resolve the issue on your own. In this section, we’ll explore each of these steps in detail to guide you through the process.

Check The Water Supply

The first step in troubleshooting your Amana washer is to check the water supply. Here’s what you need to do:

• Make sure that the water valves are open and that there is enough water pressure coming into the machine.
• Ensure that the hoses connecting the washer to the water supply are not kinked, twisted, or damaged.
• Check the water filter screen (located in the water inlet valve) for clogs. Clean the screen if there are any clogs.

Clean The Inlet Screens

Cleaning the inlet screens is another troubleshooting step. Follow these instructions to clean the screens:

• Locate the inlet screens and remove them from the washer.
• Clean them thoroughly using a brush or toothbrush.
• Once you are finished cleaning, put the screens back in place.

Check The Drain Hose

If your washer is still stuck on sensing fill, you should check the drain hose. Here’s how:

• Make sure the drain hose is not clogged, kinked, or twisted.
• Check the drain itself for any clogs or blockages.
• Ensure that the drain hose is inserted into the standpipe at least 6 inches but no more than 8 inches.

Reset The Control Board

If the previous steps do not resolve the issue, you can try resetting the control board. Here’s how:

• Unplug the washer from the power source.
• Wait for at least 5 minutes before plugging the washer back in.
• Once you’ve plugged it in, turn the washer on and select the desired cycle.

Hopefully, one of these steps will resolve your issue with the Amana washer stuck on sensing fill. Remember to always refer to the user manual for specific instructions on how to troubleshoot your washer.

More Complex Issues

Amana Washer Stuck On Sensing Fill: More Complex Issues

If your Amana washer has been stuck on sensing fill, then it is possible that you have already tried the basic fixes and are still experiencing the same problem. In such a situation, there can be more complex issues that require professional assistance.

Here are some of the most common issues:

Faulty Water Inlet Valve

The water inlet valve is responsible for allowing water to enter the washer. If the valve is damaged or faulty, then it may prevent water from entering the washer. Here are some of the signs of a faulty water inlet valve:

• The washer is stuck in the sensing fill cycle.
• The washer doesn’t fill with water or fills very slowly.
• There is a constant buzzing/humming sound coming from the valve.

To fix this issue, you will need to replace the water inlet valve. Provide a link to where such a replacement kit may be purchased.

Malfunctioning Pressure Sensor

The pressure sensor is responsible for detecting the water level in the washer tub. If the sensor is malfunctioning, then it may prevent the washer from filling up with water. Here are some signs of a malfunctioning pressure sensor:

• The washer is stuck in the sensing fill cycle.
• The washer doesn’t fill with enough water and adds water intermittently.
• The washer doesn’t stop filling up with water and overflows.

To fix this issue, you will need to replace the pressure sensor. Provide a link to where such a replacement kit may be purchased.

Control Board Issue

If the washer’s control board is damaged or faulty, then it may prevent the washer from functioning properly. Here are some signs of a control board issue:

• The washer is stuck in the sensing fill cycle.
• The washer doesn’t complete cycles or stops mid-cycle.
• The washer doesn’t respond to any commands.

To fix this issue, you will need to replace the control board. Provide a link to where such a replacement kit may be purchased.

It is essential to address these issues as soon as possible to avoid further damage to your Amana washer. Professional assistance may be necessary, especially for the water inlet valve and control board replacement. Don’t hesitate to contact a professional for assistance.

Frequently Asked Questions On Amana Washer Stuck On Sensing Fill

Why Does My Amana Washer Get Stuck On Sensing Fill?

This issue can occur due to clogged filter screens, faulty water inlet valves, or malfunctioning sensors.

How Can I Fix My Amana Washer When It’s Stuck On Sensing Fill?

To resolve this problem, you can try cleaning the filter screens, replacing the water inlet valves, or resetting the washer.

Can I Reset My Amana Washer To Fix The Sensing Fill Problem?

Yes, you can try resetting your washer by unplugging it from a power source for a few minutes and then plugging it back in.

Will Replacing The Water Inlet Valve Fix My Amana Washer’s Sensing Fill Issue?

Replacing the water inlet valve can help fix this issue, as a faulty valve can cause issues with water intake into the washer.

Should I Call A Professional To Fix My Amana Washer’S Sensing Fill Issue?

If the issue persists after trying basic troubleshooting steps, it may be best to call a professional to avoid causing further damage to your washer.

Conclusion

Overall, when dealing with an Amana washer stuck on sensing fill, it is important to first try some common troubleshooting measures before calling in the professionals. Checking for simple issues like clogging or improper power supply can potentially save you a lot of time and money.

It is also important to follow proper safety precautions whenever working with electrical appliances. If all else fails, don’t hesitate to reach out to Amana customer service or a repair technician for assistance. And finally, by taking proper care of your washer through regular cleaning and maintenance, you can prevent issues from occurring in the first place.

Remember to always prioritize the safety and functionality of your appliance to ensure it serves you well for years to come.