Ge Dishwasher Heated Dry Not Working: Troubleshoot Guide


The most likely cause of a Ge dishwasher not heating up during the dry cycle is a malfunctioning heating element or thermostat. It’s crucial to test these components and replace them if they’re faulty to ensure the dishwasher’s optimal performance.

A dishwasher is an essential kitchen appliance that helps with dish-cleaning tasks, saving you time and effort. However, when the dishwasher’s heated dry function stops working, it can be frustrating and lead to wet dishes being left behind. The heated dry feature in a Ge dishwasher uses a heating element and a thermostat to dry the dishes.

If it fails to work, the dishes come out wet and still require wiping off. This problem can be caused by a malfunctioning heating element, a faulty thermostat, or a broken timer switch that controls the drying cycle. In this article, we’ll discuss the troubleshooting steps to help you diagnose and solve the issue.

Ge Dishwasher Heated Dry Not Working.jpg

Understanding The Heating Element: Common Culprit Of A Non-Functioning Heated Dry

If your ge dishwasher is not drying dishes properly, the heating element may be the underlying issue. The heating element in a dishwasher is responsible for heating up the air inside the dishwasher and evaporating the water from the dishes.

A malfunctioning heating element can leave your dishes spotted and damp. Here’s what you need to know about the heating element in your GE dishwasher so you can better diagnose the problem.

Brief Introduction About Heating Element

The heating element is an important component of your dishwasher, and it is usually located at the bottom of the appliance. This element uses electricity to heat the air inside the dishwasher, which dries the dishes and eliminates excess moisture.

How Does The Heating Element Work In A Dishwasher?

The heating element in a dishwasher works in collaboration with other components such as the rinse aid and the drying fan. Here’s a quick overview of how the heating element works:

  • The heating element is turned on during the drying cycle
  • The heating element heats up the air inside the dishwasher
  • Water droplets on the dishes evaporate when the heated air comes in contact with them
  • The drying fan then removes the moist air, leaving your dishes thoroughly dried

What Happens When The Heating Element Fails To Function?

A non-functioning heating element can leave water droplets on the dishes and can cause damage to the dishwasher itself. Here are some common signs that indicate that your heating element may not be working properly:

  • Dishes are still wet after a complete cycle
  • There is visible damage to the heating element
  • You notice a burnt smell coming from the dishwasher
  • The cycle time has significantly increased

How To Confirm That Heating Element Is The Culprit Of Non-Functioning Heated Dry?

To confirm that your heating element is the cause of your dishwasher’s heating issue, here is what you can do:

  • Check the heating coil for any visible damage
  • Use a multimeter to test the heating element for continuity
  • Make sure your dishwasher rinse aid is not empty, as this can affect the drying process
  • Check the dishwasher manual to ensure that you are using the appropriate setting for optimal drying performance

By following these steps, you should be able to determine if your heating element is functioning properly or if it’s time to replace it. A functional heating element is integral for your dishwasher to perform at its best and leave your dishes spotless and dry after every cycle.

Fixing The Heating Element: Step-By-Step Guide

Ge Dishwasher Heated Dry Not Working

Has your ge dishwasher stopped drying your dishes effectively? If so, you may need to fix the heating element. Follow this step-by-step guide to repair the heating element in your dishwasher.

Safety Precautions To Take Before Fixing Heating Element

Before you start fixing the heating element in your dishwasher, it’s important to take proper safety precautions. Here are some tips to keep in mind:

  • Turn off the dishwasher and unplug it from the power source before starting any repairs.
  • Wear rubber gloves and eye goggles to protect yourself from any electrocution or chemical burns.
  • Double-check all the wires and circuit breakers before getting started to rule out any electrical problems.

Materials Required To Repair The Heat Element

To fix the heating element in your ge dishwasher, you will need some materials. Here’s a list of what you’ll need:

  • A multimeter to test the heating element’s resistance.
  • A screwdriver to remove any panels and access the heating element.
  • A replacement heating element (if the old one is broken).
  • Some electrical tape and a wire stripper, if there’s any wire damage.

Step-By-Step Guide To Fix Heating Element In A Dishwasher

Now that you have your materials and safety measures in place, you can get started on fixing the heating element in your ge dishwasher. Here’s a step-by-step guide to follow:

  • Remove the bottom panel of the dishwasher and locate the heating element.
  • Use your multimeter to check the heating element’s resistance. If it’s not heating up, it may be damaged.
  • Turn off the dishwasher’s power source and unplug it from the wall.
  • Use a screwdriver to remove the screws holding the heating element in place.
  • Check the wires and connections leading to the heating element. If there’s any damage, you’ll need to replace them.
  • Install the new heating element and reattach any wires and connections.
  • Replace the bottom panel of the dishwasher.
  • Turn the dishwasher back on and test it to see if the heating element is working correctly.

What To Do When The Heating Element Is Broken Beyond Repair?

In some cases, the heating element in your ge dishwasher may be broken beyond repair. When this happens, you’ll need to replace it. Here are some steps to take when replacing a broken heating element:

  • Purchase a replacement heating element (you can find this online or at a local appliance repair store).
  • Turn off and unplug your dishwasher from the wall.
  • Follow steps 1-4 in the step-by-step guide above to remove the broken heating element.
  • Install the new heating element and reattach any wires and connections.
  • Test your dishwasher to ensure everything is working properly.

Fixing a heating element in your ge dishwasher is not as hard as it seems. This guide should help you navigate the process safely and successfully.

Check The Dishwasher Timer: Another Culprit Of Non-Functioning Heated Dry

When you are dealing with a dishwasher that has a heated dry not working, the timer may also be a culprit. Here’s what you should know about the dishwasher timer.

Introduction To Dishwasher Timer

The dishwasher timer is an essential component of the appliance. It signals the dishwasher when to start and stop running. A timer malfunction can lead to a heated dry not working.

How Does Dishwasher Timer Work?

The dishwasher timer consists of a motor that activates the timer contacts connected to the heating element, pump motor, and other component-specified time intervals. Here’s how the process works:

  • The user selects the wash program, and the timer proceeds to the wash cycle.
  • The dishwasher timer regulates how long the dishwasher goes through the wash cycle.
  • Once adjustments are programmed, the timer motor turns the dial knob, and contacts are set in motion to execute various operations during the cycle.

Signs That Indicate Dysfunctional Dishwasher Timer

If your dishwasher timer has gone bad, it may display the following indicators:

  • The dishwasher fails to complete cycles, goes past the rinse cycle, and displays some error codes.
  • The timer dial gets stuck and doesn’t advance
  • The dishwasher may turn on spontaneously due to a short-timer motor winding that receives consistent voltage from the dishwasher control board.
  • The timer knob falls off or results in some electrical sparks.

How To Confirm If Dishwasher Timer Is Malfunctioning?

Here’s how to know if you are dealing with a malfunctioning dishwasher timer:

  • If you notice that the dishes aren’t clean enough or the heated dry is not working, set your dishwasher to an extended cycle.
  • Observe if the dial moves periodically. If it doesn’t move, you may need to replace it.
  • If it strikes, you may have a timer motor problem, which will require a replacement or a professional repair.

Remember, if the timer is malfunctioning, it can cause your dishwasher to stop working correctly. To keep your dishes spotless and ensure your dishwasher’s longevity, it’s crucial to sort out any timer-related issues as soon as possible.

Replacing Dishwasher Timer: Step-By-Step Guide

Ge Dishwasher Heated Dry Not Working

If your dishwasher’s heated dry feature is not working properly, one potential culprit could be a faulty timer. Here is a step-by-step guide to replacing your dishwasher timer to get your heated dry feature up and running again.

Safety Precautions Before Starting The Timer Replacement Work

Replacing your dishwasher timer is an easy DIY project, but it is important to take some safety precautions before starting the work:

  • Turn off the dishwasher’s power supply by unplugging the appliance or turning off the circuit breaker.
  • Wear safety gloves to protect your hands while handling the dishwasher’s internal components.
  • Disconnect the dishwasher’s water supply before beginning work.

Materials Required For Replacing Dishwasher Timer

To replace your dishwasher timer, you will need the following tools and materials:

  • Screwdriver
  • Wrench
  • New dishwasher timer (model-specific)

How To Replace Dishwasher Timer In A Few Simple Steps

Follow these simple steps to replace your dishwasher timer:

  • Remove the dishwasher’s front panel by unscrewing the screws on each side.
  • Locate the dishwasher timer, which is usually situated near the control panel.
  • Disconnect the wiring from the old timer by pulling the wires out of their connectors.
  • Use a wrench to remove the bolt holding the timer in place.
  • Remove the old timer and insert the new timer in its place.
  • Screw the bolt back in place and re-connect the wires to the new timer.
  • Replace the front panel and screw it back into place.
  • Turn on the dishwasher and test if the heated dry feature is now working.

Alternatives To Dishwasher Timer Replacement If Required

If replacing the dishwasher timer did not fix the problem, there may be other issues causing the heated dry function not to work. Other potential reasons include:

  • A malfunctioning heating element
  • A broken thermostat
  • A clogged spray arm

In these cases, it may be best to contact a professional repair person to diagnose and fix the problem.

By following these simple steps, you can replace your dishwasher timer and get your heated dry feature working again. Remember to take the proper safety precautions and consult a professional if needed.

Contacting Professional Repair Services

Ge Dishwasher Heated Dry Not Working

If your GE dishwasher’s heated dry function is not working, it might be frustrating to find your dishes wet and steaming instead of dry and sparkling clean. It’s important to note that while some dishwasher issues can be fixed by the owner, others may require the services of a professional repair technician.

In this section, we’ll take a look at when you need to contact a repair service for yourdishwasher, how to find a good service provider, things to check before booking the repair, and the cost of hiring a service professional.

Understanding When To Contact A Professional Repair Service

Here are some of the warning signs that your ge dishwasher is in need of repair, and you should contact a professional:

  • The dishwasher is leaking water on the floor
  • The dishwasher is making strange noises
  • The dishwasher fails to start
  • The door doesn’t close/latch properly
  • Dishes aren’t coming out clean
  • The dishwasher is not draining properly
  • The heated dry function is not working

If you experience one or more of these issues with your GE dishwasher, it’s best to call a professional to help diagnose and repair the problem.

Finding A Good Repair Service Provider

Here’s how to find a reliable service provider for your GE dishwasher:

  • Do some research online: Read reviews of service providers in your area.
  • Check for certifications and experience: Look for companies with experienced and certified technicians.
  • Ask for recommendations: Ask friends and family for recommendations and personal experiences with repair services.

Things To Check Before Booking The Professional Repair Service

Before booking a professional repair service for your GE dishwasher, make sure you or the technician have checked the following:

  • Check the power source: Ensure that the dishwasher is plugged in and the circuit breaker is not tripped.
  • Clean the dishwasher: Remove all clogs or debris that may be affecting the drain function.
  • Inspect the heating element: Check the heating element for signs of damage or breakage.

Cost Of Hiring Professional Repair Service

The cost of hiring a professional repair service for your ge dishwasher will depend on your location and the extent of the repairs needed. On average, the cost of a basic repair can cost anywhere from $150-300. If parts need to be replaced, the cost can be more expensive.

However, it’s important to remember that calling a professional for repairs can save you money in the long run since potential DIY mistakes can end up causing further damage to your dishwasher.

Frequently Asked Questions On Ge Dishwasher Heated Dry Not Working

Why Is My Ge Dishwasher Not Drying The Dishes Properly?

There could be several reasons for this problem, including a malfunctioning heating element, a faulty thermostat, or a problem with the timer.

How Can I Test If My GE dishwasher’s Heating Element Is Working?

You can use a multimeter to check the continuity of the heating element. If it shows no continuity, then it needs to be replaced.

What Should I Do If My GE Dishwasher’s Thermostat Is Faulty?

If the thermostat is faulty, it needs to be replaced. It is recommended to hire a professional technician to do this job.

Is It Safe To Use A Ge Dishwasher Without A Functioning Heated Dry Feature?

Yes, it is safe but it can be inconvenient as you will have to manually dry the dishes. It is recommended to get the appliance fixed as soon as possible.

How Often Should I Clean My Ge Dishwasher To Prevent Heating Problems?

It is recommended to clean the dishwasher once a month or every 30 wash cycles. Regular cleaning helps prevent problems with the heating element and other parts.


To wrap up, having a ge dishwasher with heated dry not working can be frustrating, but there are solutions to this problem. Checking the necessary components, such as the thermostat and the heating element, can often resolve the issue. Additionally, ensuring that the dishes are loaded correctly and not blocking the dishwasher’s vents is also important.

It’s vital to remember that exposing your dishwasher to hard water can cause mineral buildup, which can impact the appliance’s performance. Therefore, using the right detergent can also make a significant impact on the dishwasher’s overall functionality. With these tips, you can ensure that your ge dishwasher’s heated dry feature functions correctly and prolongs the life span of your dishwasher.

Don’t hesitate to reach out to a professional technician if needed. Happy dishwashing!

Leave a Comment